Dish Network Troubleshooting No Signal Guides

Dish Network Troubleshooting No Signal Guides [2021]

Posted by

Many issues are associating with the DISH Network service that you may be encountering, and no guide to troubleshooting no signal on your tv.

If you find it challenging to do so, then don’t worry. You’re in the right place. In this post, I’ll be explaining the DISH Network no signal troubleshooting guide step-by-step.

First and foremost, check the installed satellite dish can quickening troubleshoot this DISH TV issue; Does it mount correctly to the suitable position.

To fix the DISH Network No Signal problem, you have to check your TV’s input connection and see if it’s where the receiver cables are connected. Switch OFF/ON or reboot. If the problem persists, then you can read on.

Dish Network Troubleshooting No Signal Guides

Causes of The No Signal Problem On The Dish Network

Most of the digital providers of signal use satellite dish for receiving network from space. Therefore, some of the causes would indeed come from severe weather.

It stated in my previous post that heavy rain, snowfall, wind, trees, and buildings could be the most common things for the no signal issue. 

Besides these, yet there are some other reasons for the no signal error, such as:

1. Wrong Satellite Dish Placement

The satellite dish’s mounting incorrectly positioned start from the pole placement, in-balance surface, and both the satellite dish and accessories must not be managed.

For instance, corrosion and rust can reduce the signal or difficult to detect during installation. However, this does not say that satellite dish coated and corrosive resistant are 100% safe.

READ ALSO:

2. DISH Network Technical Maintenance

You can’t expect 100% uptime from DISH as a provider, and even SKY UK has its own down-time. Maintenance activities call for checking, repairing, and updating the whole system.

Before the maintenance time commences, the provider usually makes public notice detailing the time to carry out these scheduled activities. Some services may be shut down for a while, like payment gateway and channels loss signal.

3. UHF Antenna Misaligned

In short terms, UHF means Ultra-High Frequency antennas as add-ons to satellite and boost comprehensive coverage. In most cases, these UHF antennae are connected to the satellites scattering a signal and reception to vast regions.

Hurricanes, storms, snow, and wind can disturb and misalign the UHF antenna signal that supposes to receive by the primary antenna.

DISH Receiver

4. Wrongly Connected Cables

Sometimes, the error might not be too far. It is within your reception. The cable can get disconnected from the DISH satellite receiver.

You won’t be able to watch your favorite local TV shows, Sport and movies when the cables aren’t connected properly.

Most of these are common culprits on why you’re having no signal issues or blank black screen. It may not look very easy to fix from your view! It is easy and straightforward.

In this post, the time has explained in great detail on troubleshooting DISH Network no signal issues.

Dish Network Troubleshooting No Signal Error

DISH Network Troubleshooting No Signal – Problems/Errors And Solutions

The following are the best guide you need for troubleshooting DISH Network with No signal error relating to ports 1 and 2.

1. Check Your TV Input Connection

At here, first and foremost, You have to double-check your input cable connection and which TV mode is enabled right now on your television.

TV Remote Control Troubleshooting DISH No Signal Guide

To do this, Hold your remote control—Press SOURCE or INPUT button to change to the right mode. Alternatively, You can switch from one mode to another to check the correct input connected to your receiver.

2. Cables are Properly Functioning And Connected

Here, the next thing to do is check your receiver’s cable connection after you might have confirmed the connection is at the right source or input.

You are checking the cables connected to your receivers, such as HDMI, RCA, and components cables. Sometimes, you need to check the power cables connected to the wall socket and signal cable.

Double-check the cables if there are any damages in between these cables because it may cause service disruptions.

While ensuring that the cable is correctly connected, You can remove and reinsert each cable to confirm the cable is well plugged. In case you want to check the RCA cable, they are Red, Green, and Blue cable plug like AV.

3. Change The Input From TV

In a rare situation, the TV input might be faulty, causing the TV to have no signal. You have to interchange the input or source to troubleshoot this kind of error with Your DISH Network receiver.

TV1 or TV2 Dish Network No Signal Error

For instance, you can change from HDMI 1 to HDMI 2 or AV 1 to AV2 depend on the type of TV source or input supported by your receiver or TV to check for no signal error.

READ ALSO:

4. Dish Network Troubleshooting On TV2 With No Signal Error

Try to check the two default saved channels, one after the other. Trying tune channels 65 and 70 to see if the picture is coming up.

5. Check Connection Between The Receiver And DISH Receiver

Here, you have to check the cable connection from the TV set and to the DISH receiver. Ensuring that the cables are correctly connected and can even change the cable if not responsive or damaged.

6. Check Green Light And Standby Mode 

The green light display in the front panel indicates that the DISH receiver is working correctly. If otherwise, the light is blinking, you need a guide to troubleshoot the receiver as it will display no signal on the TV screen. You’ll need to press and hold the power button to reboot the receiver to standard. 

Standby mode as well indicates that the receiver is not in use. Just press the power button and then tap on the channel up or down button. 

Note that DISH Network has a series of remote control, and the SAT button placement is not the same on each remote version. Some are at the front side, while another version is at the backside.

7. Dish Network Troubleshooting: Factory Reset of the Receiver

Resetting the DISH receiver is very simple; you’ll need to remove the power cable from the wall socket or switch the power off from the receiver’s back. Whichever the way you adopt, make sure you wait for 10-20 seconds before power on or plug the cable back to the wall socket.

Just try these guides one after the other, and I believe you’ll troubleshoot the DISH Network system with no signal error.

Trying To Reach Dish Customer Care Support

After you have carefully followed the troubleshooting guides on Dish Network display no signal on the TV screen and still experience the error, the best thing to do is reach the Dish Support page.

The best to contact Dish is to call their hotline or through Email, explaining all the troubleshooting guides you have already undergo with your receiver displaying no signal. No matter how it is complicated. They can even allocate accredited technicians to come over to your house to fix the error with charges applied.

Please follow and like us:

Leave a Reply

Your email address will not be published. Required fields are marked *